Racine HSMM IP
From Megawiki
[edit]
What can I do if I forgot my password?
The following reset procedure will completely restore the default settings on your D-Link device including your password. This procedure applies to the DI-514, DI-524, DI-604, DI-614+, DI-624, DI-754, DI-764, DI-774, DI-784, DI-804V, DWL-800AP+, DWL-900AP+, DWL-1000AP+, DWL-2000AP, DWL-2100AP, DWL-6000AP, DWL-7000AP, and DWL-7100AP.
- Step 1 Locate the reset pinhole on the back of the unit.
- Step 2 With the unit powered on, press and hold the Reset button.
- Step 3 Hold the Reset button for about 10 seconds.
- Step 4 Release the Reset button.
- Step 5 The unit will reboot. Allow 20-30 seconds before reconnecting.
- Step 6 The device is now at factory defaults. Note: Do not recycle power during the reset procedure. The default user name for most D-Link devices is admin and the password is left blank.
[edit]
IP PLAN
Subnet mask on all devices 255.255.0.0 Important make sure to use this subnet mask at all times..
| CALLSIGN | STATIC IP | ETHERNET MAC /WIRELESS MAC | |
|---|---|---|---|
| K9DOE-1 | 192.168.5.1 | 00-0D-88-99-A3-F4/00-0D-88-9D-4A-03 | |
| KB9ZAF-1 | 192.168.5.2 | ADDRESS | |
| WA9HOH-1 | 192.168.5.3 | 00-0F-3D-AC-A4-2D | |
| WB9ZKY-1 | 192.168.5.4 | ADDRESS | |
| KB9MMA-1 | 192.168.5.5 | 00-17-3F-34-C3-C7 | |
| WB9USI-1 | 192.168.5.6 | ADDRESS | |
| N9RGX-1 | 192.168.5.7 | 00-0D-88-a5-ad-b9 | |
| KA9KJE | 192.168.5.8 | ADDRESS | |
| 192.168.5.9 | ADDRESS | ||
| HUB AP1 | 192.168.5.254 | 00-00-D8-83-32-CC-FB/ADDRESS |
| CALLSIGN | START IP | END IP |
|---|---|---|
| K9DOE | 192.168.5.10 | 192.168.5.19 |
| KB9ZAF | 192.168.5.20 | 192.168.5.29 |
| WA9HOH | 192.168.5.30 | 192.168.5.39 |
| WB9ZKY | 192.168.5.40 | 192.168.5.49 |
| KB9MMA | 192.168.5.50 | 192.168.5.59 |
| WB9USI-5 (VCRC) | 192.168.5.60 | 192.168.6.69 |
| N9RGX | 192.168.5.70 | 192.168.5.79 |
| 192.168.5.80 | 192.168.5.89 | |
| 192.168.5.90 | 192.168.5.99 | |
| VPN POOL DHCP | 192.168.5.210 | 192.168.5.235 |
| Servers reserved | 192.168.5.230 | 192.168.5.253 |
[edit]
Other network settings
- Preamble Type : Long Preamble
- SSID Broadcast : Enabled
- Basic Rates : 1-2(Mbps)
- TX Rates : 1-2-5.5-11(Mbps)
- Authentication : open system
- WEP : ENABLED Key Type ASCII, PRT97
- CH 2
The way you would connect to a station is to punch in their callsign, that will look up their IP address automatically!!! It is Domain Name Service based on callsign!
